Leading 10 common forklift accidents ， forklift operation should pay attention to these matters ！.

Don't take too lightly the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and hangs on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no obstacles that prevent the security of driving, honk the horn initially and afterwards begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is stable and trustworthy.
4. The start has to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the task website or while driving, take care that there will be no challenges in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will affect the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security distance from the automobile in front. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever operate with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special Stand-on Electric Pallet Stacker circumstances, security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the load, and it ought to be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or lower the fork structure.
2. Draw the hand brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be inspected, and fuel, lubing oil and air conditioning water need to be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " complimentary turning";.
6. Adding and down the slope should be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. Stand-on Electric Pallet Stacker It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the exact same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844